INSTALLING A JAMMER

 

 

 

Package Contents

• 2 transceiver heads with integrated cables

• 1 speaker pod with LED and volume control wheel

• Speaker Pod cable  

• 1 wiring distrubution box with 12v DC power cable 

• Wiring clips and pre-formed high temperature double back tape

• Installation manual and mounting hardware

 

Attention

• Do not disassemble or rewire the product.

• Do not use, if the product is not in good order or broken.

• Please install based upon user and installation guide.

• If the insulation is not based upon user guide the operation and effectiveness of the product may be low.

• Contamination on front end of the transceivers may affect performance.

   

 

  1. Start with mounting the two transceivers (Heads)in the front of the vehicle. These heads must be mounted correctly for optimal Jamming output. First make sure you find the best placement area on the vehicle. Remember the officers are trained to shoot for the front license plate first and then go on to the headlights. They look for the most reflective spot on the target vehicle. We recommend placing the heads in the best location based on this information. Each  brand and model vehicle of course will be different. Choose the location closest to the specifications in the manual and within this installation article below.

 

 

 Examples of different type installs.

 

 

 

 

            

 

 1 Mounting the transceivers

LaserMask is one of the most effective laser jamming systems on the market today. Designed by industry experts, manufactured to exact specifications and tested and certified by world-renowned laboratories.

LaserMask is the world's finest laser jamming system built with high quality components and precision tuned to afford long life under extreme environmental conditions. With proper care and maintenance your LaserMask will provide year round protection and a long life.

Although users are able to install the LaserMask themselves, to assure optimum performance it is highly recommended a professional install this product.

Professional installation shop; please read the entire installation guide and carefully follow the instructions.

2 Adjusting the transceivers

After making sure the transceivers are mounted correctly read further for determining top or bottom of transceivers. The bracket is attached correctly out of the box. Make sure the unit is mounted with the bracket on top. Never mount the unit with the bracket on the bottom, The heads must be level to the road and we suggest using a small bubble level this is very important. This will allow the LaserMask to perform properly with maximum Jamming power output. 

3 Setting Up Interface Box

        Locate a suitable place for the interface box inside the car's interior. Normally this is on the drivers side under the dash close to the fuse box and positive + 12 volt wiring locations. We do not recommend the interface box being mounted in the engine compartment because of moisture, heat, vibration etc.. I some cases you may not have a choice or it would be much easier to install in the engine compartment. NOTE if mounted in engine compartment the head must be placed in a extremely protective location with the interface enclosed in a water tight enclosure. A professional installer should have no problem with this type of install. The cables from the transceiver heads mounted in front are plugged into two of the jacks on the interface box.

Connect the red wire (positive+) from the interface box to a 12 Volt power supply that is activated when the key is on. Connect the black wire (negative -) to a suitable ground.

Place a strip of double back tape on the interface box and mount to vehicle pressing firmly for a secure attachment.

4 Installing Laser Alert Speaker

        Locate a suitable place for the laser alert speaker. The unit is often located on the dashboard. For a less noticeable installation select a location lower than the dash board. Some users chose to locate the unit underneath the dashboard. However, in this type of installation the red LED will not be visible and we recommend the volume is set on high.

Once mounted with the double back tape, route the speaker wire through the body of the vehicle to the interface box and connect the cable. Connect the other end to the speaker and set the volume to mid range. Adjust the volume to your preference once the system is activated.

5 Operation

When the engine is started the system will go through a self check and the LED light will go from red to green in a few seconds.  When the engine is off the LED should be off. If the LED does not come on the device is not working properly. Check power and cable connections. Important information the LaserMask is designed to be fully automatic and will only turn on when engine is running. You never have to worry about system being tuned on or off. Some customers like to add a switch to the interface to manually shut the system down after being targeted and your vehicle has slowed to posted speed limit. This will allow law enforcement to get a proper reading which would be more like a normal encounter to them.

6 Product Registration

Please fill in and mail the enclosed product registration form in by postal mail. By sending in the registration form we can offer technical assistance and all the provisions of the warranty.

Remark

  1. Installation and operation as outlined in this manual is required to meet warranty provisions. LaserMask does not take responsibility for problems or poor results due to the user not following this guide.

  2. What to do when alarm sounds?

    As soon as the alarm sounds immediately verify that your speed is within legal limits. Adjust your speed as appropriate. Maintain your speed within the limits allowed. At this point the system is immediately rearmed for the next laser detection. (Notice : If the speaker is removed from the system, the power of lasermask will be turned off.)

Installation Diagram

 

     

Heads should be mounted 23 to 27 inches or 60cm to 70cm apart.

WARNING!!

WARNING!
Do not look directly into the transceivers with the naked eye at close range. You will not see anything but this might cause eye damage after prolonged exposure. Remember the laser emits infrared light which is not visible to the human eye regardless of how strong it is.

In no way does LaserMask advocate exceeding legal speed limits or any traffic laws. We are not responsible for any injuries, accident or traffic violations that might occur due to improper installation or usage of this product.

A professional installation is highly recommended !!

 


 

 
Below is the Custom LCM-3 option Installation Diagram